How To Use A Keurig Compact

Keurig 1000-Compact Single Serve Java Brewer User Manual

Keurig K-Compact Single Serve Coffee Brewer

Get the about from your new Keurig® brewer

Before Y'all Brew

ane.Plug & Place

Remove packing record from brewer and plug into a grounded outlet.
Place a large mug (x oz. minimum) on the baste tray plate.

Plug & Place

2. Rinse & Fill

Remove the h2o reservoir chapeau, then lift the reservoir directly upwards to remove it.
Rinse reservoir with fresh water and fill to the MAX line.
Replace water reservoir, making certain the lock tabs appoint with the brewer.
Replace lid.
NOTE: Do not apply distilled water.

Rinse & Fill

iii. Power On

Press ability push button—the greenish power low-cal will illuminate.
The brewer will automatically begin heating the water. This will accept nigh 4 minutes. Once the heating sound stops, the brewer is ready.

Power On

four. Lift & Lower

Elevator and lower the handle. Do not insert a 1000-Cup® pod. The three brew buttons volition glimmer.
Press the small-scale loving cup push to commencement a cleansing brew. Pour the hot water into the sink.
The one-fourth dimension setup process is at present complete and you are gear up to brew!

Lift & Lower

5. Place Mug

Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and identify the mug on the baste tray base of operations.
Annotation: Between brew cycles, the brewer may take about a minute to reheat.

Place Mug

half dozen. Lift & Insert

Lift the handle and place a K-Loving cup® pod in the M-Cup® pod holder. Lower the handle
completely to shut the hat.
Do not remove the foil lid on the K-Loving cup® pod.

Lift & Insert

7. Mash & Enjoy

Select your brew size. The button volition remain illuminated while brewing—about one minute. Brewing ends with a outburst of air.
Lift the handle and dispose of the used K-Cup® pod. The brewer volition be ready to brew another cup in most a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift and lower the handle completely.
Circumspection: While brewing, there is extremely hot h2o in the K-Cup® pod holder. To avoid injury, practice not lift the handle during the brewing process.

Brew & Enjoy

Brewer Features

Smart Start heats so brews in ane simple process. No need to expect for the brewer to heat earlier selecting brew size. Ability on your brewer, place mug, insert a K-Cup® pod, and lower the handle. Then, select your mash size. The brewer will rut, then automatically begin brewing.
Machine Off automatically turns your brewer off 2 hours later the last mash for free energy savings.

Brewer Features

Caring for your Brewer

Regular cleaning keeps your brewer running smoothly. Ever be sure to turn off and unplug your brewer before cleaning.

Brewer Outside

Proceed your Keurig® brewer looking its best past cleaning the exterior from time to time. Just make clean with a damp, soapy, lint-free, not-annoying cloth.
Never immerse the brewer in water or other liquids.

Brewer Exterior

Baste Tray

The baste tray tin can accumulate upwards to 8 ounces of overflow and should exist emptied and cleaned occasionally. To remove, slide it toward you, keeping it level to avert spilling. Clean in dishwasher (tiptop rack only) or rinse and clean with a damp, soapy, lintfree, non-annoying cloth.

Drip Tray

Water Reservoir & Reservoir Lid

The water reservoir lid and water reservoir should be periodically cleaned with a damp, soapy, nonabrasive cloth and rinsed thoroughly.

The water reservoir lid and water reservoir should not be put into the dishwasher. Practice not dry out the inside of the h2o reservoir with a cloth as lint may remain.

To clean the filter screen at the base of your h2o reservoir, empty the water reservoir and follow one or all of the following procedures:

Water Reservoir & Reservoir Lid

Rinse the filter screen with the strong force of water from your faucet.
If yous have a sprayer, aim the water spray at the filter screen.
Make full the h2o reservoir with approximately ii inches of clean h2o and arouse (shake) the water reservoir. Empty the water reservoir, fill with clean water, and render it to the brewer. If needed, echo above procedures.
CAUTION: Please rinse the water reservoir thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions remain in this expanse every bit they may contaminate the water supply in the brewer.

G-Cup® Pod Holder Assembly

K-Cup® Pod Holder Assembly

To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the height of the M-Cup® pod holder with one hand while pushing up on the bottom of the 1000-Loving cup® pod holder
from underneath with the other until it releases. After cleaning, align the K-Cup® pod holder with the opening using the two front ribs as a guide and snap into place from the top.

CAUTION: There are sharp needles that puncture the K-Loving cup® pod to a higher place the K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of injury, exercise not put your fingers in the Grand-Cup® pod holder.

Funnel

The funnel can be removed from the K-Cup® pod holder past pulling on it until it pops off. To supplant information technology, simply snap information technology back onto the K-Cup® pod holder.

Funnel

Get out Needle

Remove the pod holder associates and disassemble the funnel. Locate the exit needle on the inside bottom of the Thousand-Loving cup® pod holder. Insert a straightened paper clip into the exit needle to loosen the clog and push information technology out.

Exit Needle

Entrance Needle

Lift the brewer handle and locate the archway needle on the underside of the hat. To make clean both holes in the needle, hold the brewer handle in the upward position and with your other mitt, carefully insert a straightened paper clip into both holes. Gently move it around to loosen any coffee grounds. Lower the handle completely and run two water-merely brew cycles. Do not insert a K-Loving cup® pod.

TIP: Refer to www.Keurig.com/support for video instructions on cleaning the entrance/exit needles.

Descaling your Brewer

You should descale your brewer every three-6 months. Properly follow the descaling procedure.

Depending on the mineral content of your water, calcium deposits or scale may build upward in your brewer. Scale is nontoxic only if left unattended tin can hinder brewer functioning. Regularly descaling your brewer every 3-6 months helps maintain the heating element, and other internal parts that come in contact with water. Calcium deposits may build up faster, making information technology necessary to descale more than often.

Descaling Procedure

Before yous brainstorm, y'all will need a large ceramic mug, fresh water, Keurig® Descaling Solution, and access to a sink. Do non employ a newspaper cup. Ensure that in that location is no potable pod in the One thousand-Cup® pod holder. Please permit approximately 45 minutes for the descaling procedure.

Footstep 1: Descaling Solution Rinse

Press the power push to power the brewer off.

Pour the entire bottle of Keurig® Descaling Solution into an emptied water reservoir. And so make full the empty bottle with water and cascade into the water reservoir. Press the power button to plow the brewer back on.

Place a big mug on the baste tray and run a rinsing brew by lifting and lowering the handle and selecting the largest brew size.

STEP 2: Descaling Rinse & Echo

Echo the rinsing brew process until the add together h2o low-cal is illuminated. Do non use a K-Cup® pod. Let brewer stand up for at to the lowest degree 30 minutes while still on.

After 30 minutes, discard any residue solution from the water reservoir and rinse thoroughly.

Pace 3: Fresh Water Rinse

Make full the water reservoir with fresh water to and not across the MAX line.

Place a large mug on the drip tray plate and run a rinsing mash using the largest brew size. Do not use a Chiliad-Cup® pod. Pour the contents of the mug into the sink.

Echo mash process until yous have completed at least 12 rinsing brews using the largest mash size. Y'all may need to refill the h2o reservoir at least once during this process.

Notation: The cleaning action of Keurig® Descaling Solution may result in a "foam" dispensed from the brewer. This is natural, as the solution is reacting with the calibration inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, yous may run into only a small or no output dispensed, followed by the sound of air blowing out. If this occurs:

Turn off and unplug the brewer.
If there is Keurig® Descaling Solution in the water reservoir, discard the contents, rinse the water reservoir thoroughly and refill with water.
Plug the brewer back in, power on, and repeat the Stride 3 Fresh H2o Rinse cycle. The brewer should begin to function normally equally the solution is rinsed out and the calibration is removed. If problem persists, allow brewer to sit unplugged for at least 30 minutes before standing with the rinse.

Troubleshooting

Grounds in Your Coffee

Grounds may have gathered in the exit or entrance needle and tin exist cleaned using a straightened paper clip or similar tool.

Clean the exit needle of the K-Loving cup® pod holder. Refer to the exit needle care instructions.
Clean the brewer entrance needle. Refer to the entrance needle care instructions.

Brewer Will Not Brew

After placing the K-Cup® pod in the Thou-Cup® pod holder, make certain that the handle is pushed down securely and the brew buttons are flashing.
If the add together water low-cal is illuminated, add together water to water reservoir. Fill up to and not beyond the MAX line. Make certain the water reservoir is seated properly in its base. If the add h2o light continues to be illuminated even after refilling, contact Customer Service.
If the minor cup, small mug, and large mug lights are all on simultaneously, elevator handle and remove K-Cup® pod (if present in the brewer). Shut handle and place a big mug on the
drip tray. Press the power button once. The brewer may manipulate hot water.
If the pocket-sized cup, small mug and large mug lights all glimmer simultaneously, contact Customer Service.

Brewing a Fractional Loving cup

The exit needle may exist clogged. Refer to the get out needle care instructions.
The water reservoir may have been removed during brewing. Replace the h2o reservoir and perform a rinsing brew without a K-Loving cup® pod.
The brewer may need to be descaled. If you have repeated the descale procedure on your brewer two times and it is even so simply brewing a fractional cup, contact Customer Service.

Brewer Does Not Accept Power or Shuts Off

Make certain that the ability button has been turned on.
Plug brewer into its own grounded outlet. If the electric excursion is overloaded with other appliances, your brewer may non part properly. The brewer should be operated on its
own circuit, separate from other appliances.
For energy savings, the brewer automatically turns off ii hours after the last brew. Press the power button and the green power lite will illuminate.
If the brewer even so doesn't have power, contact Customer Service.

Helpful Hints

Water quality varies profoundly. If yous notice an undesirable sense of taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Exercise not use distilled water.

Service

Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.

Storage

Empty the water reservoir before storing or transporting and accept care to ensure that y'all shop your brewer in a safe and frost free surround. Please be sure to store your brewer in its upright position to avoid water leakage from the inner tank. If you store the brewer in a cold environment, you run the chance of water freezing within the brewer and causing harm. When you set up to use it after storage, we recommend rinsing the h2o reservoir with fresh h2o and running 3 rinsing brews without a K-Loving cup® pod.

If you plan to move your brewer to a different location, plow the brewer off, unplug it, and empty the water reservoir. If your brewer has been in an environment below freezing, please be sure to permit information technology warm to room temperature for at to the lowest degree 2 hours before using.

Click or Call!

Have Questions?

Nosotros're here to aid. Visit world wide web.Keurig.com/back up for step-by-footstep videos on cleaning, descaling, and more.

Still Need Help?

Call

Give us a telephone call at one-866-901-BREW (2739)

Warranty

Limited I Yr WARRANTY

Keurig Green Mountain, Inc. (Keurig) warrants that your brewer will be free of defects in materials or workmanship under normal dwelling use for one year from the date of purchase. It is recommended that you register your brewer on www.Keurig.com/new then that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without accuse upon its receipt of proof of the engagement of buy. If a replacement brewer is necessary to service this warranty, the replacement brewer may be new or reconditioned. If a replacement brewer is sent, a new limited one year warranty volition be applied to the replacement brewer.

This warranty only applies to brewers operated in the United states of america and Canada. This warranty gives you specific legal rights, and you may also accept other rights that vary from state to country and, in the case of Canada, from province to province.

Only the apply of Keurig® K-Cup® brand pods and accessories will guarantee the proper functioning and lifetime of your Keurig® brewer. Any damage to or malfunction of your brewer resulting from the use of non-Keurig® pods and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to exist caused past such use.

WHAT IS NOT COVERED BY THE LIMITED WARRANTY?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES Non COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM Any Breach OF THIS WARRANTY, Fifty-fifty IF FORESEEABLE.

Some states or provinces practise non allow the exclusion or limitations of incidental or consequential amercement, so the above limitation or exclusion may not apply to y'all depending on the land or province of purchase.

Nor does this warranty comprehend amercement caused by utilize of non-Keurig® pods or accessories, services performed by anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig® parts, or external causes such as abuse, misuse, inappropriate ability supply, or acts of God.

OTHER LIMITATIONS

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF Whatsoever OTHER Limited WARRANTY, WHETHER WRITTEN OR ORAL. IN Improver, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR
K-COMPACT™ BREWER, INCLUDING ANY Implied WARRANTY OF MERCHANTABILITY OR Fettle FOR Whatsoever PARTICULAR PURPOSE.

Some states or provinces do not let disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may non utilize to you depending on the state or the province of purchase.

HOW DO You OBTAIN WARRANTY SERVICE?

Keurig® brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. Still, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll free phone number i.866.901.BREW (2739). Please do not render your brewer for servicing without beginning speaking to Keurig Customer Service to obtain a Return Materials Authorization (RMA) number. Keurig® brewers returned without a RMA number volition exist returned to the sender without servicing.

Chiliad-COMPACT™ BREWER

K-COMPACT™ BREWER

A. Water Reservoir Lid
B. MAX Fill Line
C. Water Reservoir
D. Water Reservoir Lock Tab Slots
Due east. Power Cord
F. Handle
G. Lid
H. K-Cup® Pod Holder (H and I are the One thousand-Cup® Pod Holder Assembly)
I. Funnel
J. K-Cup® Pod Associates Housing
Grand. Drip Tray Plate
L. Drip Tray
M. Drip Tray Base

For replacement parts, please visit www.Keurig.com

Fully experience the benefits that come with your new Keurig® brewer at

KEURIG.COM/NEW

Keurig